Today we will be introducing you to the steps on how to replace garage door cable. This article will make you learn how to fix overhead springs of garage doors plus wires. Furthermore, it is without visiting the emergency room.
Moreover, there are some tools and materials that will be required to replace the garage door cable. You will also learn what a tension spring on a garage door does. There are nine steps in total for the whole process. Competition of the process will require some accessories which you need to purchase.
Precautions one must need to take before carrying any operation. Garage doors are pretty heavy. Hence when you disassemble the torsion spring, keep yourself safe. The torsion spring provides a counterbalance to make the lifting process easier. Meanwhile, check out our other informative article on how to bypass garage door sensors.
How to replace garage door cables and springs
You will need some tools in order to repair the garage door cables. So the tools are listed below for your ease.
- Flexible wrench
- Heavy-duty hammer
- Gloves (leather preferable)
- Locking pliers
- Safety glass
- Socket set
- Winding bars
- Set of wrench
- Bottom brackets
- Double life torsion spring
- Cable ties
Facts about garage door torsion springs
During the repairing process, many things can go wrong. Do not panic as most of the items are easy to fix. However, remember that problems that involve garage door torsion springs can be problematic.
A garage door torsion spring has vital work to do. They provide a repulsive force to make the lifting process easier for heavy doors. So if you treat them carelessly, you might end up hurting yourself.
How to replace garage door spring
You will be able to replace garage door spring if you follow the steps carefully successfully. The springs provide a substantial twisting momentum on the torsion tube in order to lift the heavy garage door. The drums which are present at the end of the tubes act as reels. Those winds up cables which are connected to the door. The most seen common problem with the system is cables or broken springs. Moreover, smaller doors are equipped with only one spring.
Read further to know more about how to replace the garage door cable.
A stepwise guide on how to fix garage door cables
How To Fix Garage Door Cable? We are here to let you know how to replace garage door cables and springs. Therefore, a step-by-step is given for your convenience and easy learning.
In the first step, you will lock the door and clamp the door. The door should be clamped to the track.
Moreover, do clamp locking pliers to track. This is immediately above the roller.
In this step, make the unbroken spring lose. First of all, position a winding bar to the bottom hole. Remember to the bottom hole should be of a winding cone—furthermore, the winding cone of the right spring. Now just hang tightly. This will make the spring push powerfully.
At this step, disassemble the unbroken spring. Moreover, you should make use of the two winding bars. What you should do in this step is to put the 2nd winding bar onto the hole. Make sure to insert it at a 9.00 position.
Finally, take off the bottom bar—furthermore, take off the spring, Passover winding bard within each turn. Read further to know more about how to replace garage door cable.
In this step, unmount those springs located at the center bracket. Furthermore, remove bolts and also nuts.
To secure the torsion tube in this step. Take the help of lock pliers to do so. Then, in the center, the bracket fits the lock pliers. This will help to keep the torsion tube in the bracket. Furthermore, make the setscrew lose on left & right cable lift drums. Finally, take off the lift cables to disconnect them.
Finally, remove the older spring. Then slide over the torsion tube.
Moreover, buy the replacement parts and do calculate the diameter of the wire. Also, determine the spring’s hand. You should do that by looking at the end of each spring. Read further to know more about how to replace the garage door cable.
Now fit the left spring. Moreover, reassemble to hang to the breaking bracket.
Get a new center bearing. Then connect the stationary cones to the center bracket.
Finally, get the bottom brackets replaced. Also, do replace the lift cables and rollers.
Remember to clean the rust parts. Replace rusted parts with new parts. Moreover, thread the cables. You should make the cable anchor in the slot.
Just make the drums tight in this step. Be careful to tight the drums equally. Otherwise, the tension will vary.
Finally, follow the recommendation of the spring supplier and wind the tension spring. Then make the spring stretch. Do press the winding bar.
Remember to give enough lubrication to the spring.
And you are done!
Hopefully, your problem was solved on how to replace garage door cable. Moreover, before you finish the work, please do test the torsion spring. Torsion spring might not work intended.
This can be due to several reasons. You might have failed to fit the accessories properly. And, you might have made some measurement mistakes. Furthermore, the torsion spring which you brought new might not be fit in with your frame. There are several other reasons. We advise you to visit a pro mechanic so that he can fix your garage door cable.
The processes might seem easy, but they are not that easy. They require precision from experts. Here is a commons sense. If no experts were needed, why would people hire 20 years of experience mechanics rather than one year of an experienced mechanic?
This was all about how to replace garage door cable. Thanks for considering our article. Thanks!
You may find it interesting to read our next article on how to get better gas mileage in Dodge RAM 1500?
Hi, it’s Md Anwar H.
CSE (Computer Science & Engineering) & MSC from Port City International University.
Working infield of WordPress, eCommerce Develop, SEO, Digital Marketing, Google AdSense an Affiliate Marketing Since 2010.
Google AdWords/Google Ads Display.